WINTERIZING YOUR BOAT

WINTERIZING YOUR BOAT

Your first step in winterizing should be to make a checklist of all items that need to be accomplished. Check the owner’s manual of your boat and motor(s) for manufacturer’s recommendations on winterization. If you are a new boat owner, perhaps you should employ the assistance of a friend with experience in winterizing or hire a professional to do the job. The following is a generic outline of areas which should be of concern to you, however, there are many resources on the Internet with more detailed and specific information.

INBOARD ENGINE(S)

You should run the engine(s) to warm it up and change the oil while it is warm. This tends to allow impurities to be drained away with the oil. You should also change the oil filter(s). Flush the engine(s) with fresh water. You should circulate antifreeze through the manifold by using a pickup hose from the waterpump to a bucket of antifreeze. Start the engine and allow the antifreeze to circulate until water starts to exit the exhaust. This process will vary slightly depending on whether you have a “Raw Water” cooling system or an “Enclosed Fresh Water” cooling system. Make sure you have a way to catch the antifreeze expelled. If you have a wet exhaust muffler, make sure you drain it. While you’re in the engine room you should also change the fluid in your transmission. Remove spark plugs and use “fogging oil” to spray into each cylinder. Wipe down the engine with a shop towel sprayed with a little fogging oil or WD-40.

STERN DRIVE(S)
You should thoroughly inspect the stern drive and remove any plant life or barnacles from the lower unit. Drain the gear case and check for excessive moisture in the oil. This could indicate leaking seals and should be repaired. Clean the lower unit with soap and water. If your stern drive has a rubber boot, check it for cracks or pinholes. Grease all fittings and check fluid levels in hydraulic steering or lift pumps. Check with your owner’s manual for additional recommendations by the manufacturer.

OUTBOARD ENGINE(S)
Flush engine with fresh water using flush muffs or similar device attached to the raw water pickup. Let all water drain from the engine. Wash engine down with soap and water and rinse thoroughly. Disconnect fuel hose and run engine until it stops. It is important to follow a step by step process to make sure that all fuel is drained from the carburetor to prevent build-up of deposits from evaporated fuel. Use fogging oil in the cylinders to lubricate the cylinder walls and pistons. Apply water resistant grease to propeller shaft and threads. Change the gear oil in the lower unit. Lightly lubricate the exterior of the engine or polish with a good wax.

FUEL
Fill your fuel tank(s) to avoid a build up of condensation over the winter months. Add a fuel stabilizer by following the instructions on the product. Change the fuel filter(s) and water separator(s).

BILGES
Make sure the bilges are clean and dry. Use soap, hot water and a stiff brush to clean up any oil spills. Once the bilges are clean, spray with a moisture displacing lubricant and add a little antifreeze to prevent any water from freezing. Fresh Water System Completely drain the fresh water tank and hot water heater. Isolate the hot water heater by disconnecting the in and out lines and connect them together. Pump a non-toxic antifreeze into the system and turn on all the faucets including the shower and any wash-down areas until you see the antifreeze coming out. Also put non-toxic antifreeze in the water heater.

HEAD
Pump out the holding tank at an approved facility. While pumping, add fresh water to the bowl and flush several times. Use Vanish cry stals or whatever your owner’s manual recommends that will not harm your system and let sit for a few minutes. Again add fresh water and pump out again. Add antifreeze and pump through hoses, holding tank, y-valve, macerator and discharge hose. Again, check your owners manual to make sure that an alcohol-based antifreeze won’t damage your system.

INTERIOR
Once you have taken care of the system you should remove any valuables, electronics, lines, PFDs, fire extinguishers, flares, fenders, etc. Over the winter these items can be cleaned, checked and replaced as necessary. Open all drawers and lockers and clean thoroughly. Turn cushions up on edge so that air is able to circulate around them or, better yet, bring them home to a climate controlled area. Open and clean the refrigerator and freezer. To keep your boat dry and mildew-free you might want to install a dehumidifier.

OUT OF WATER STORAGE
Pressure wash hull, clean barnacles off props and shafts, rudders, struts and trim tabs. Clean all thru-hulls and strainers. Open seacocks to allow any water to drain. Check the hull for blisters and if you find any that should be attended to you might want to open them to drain over the winter.
By following some of the above suggestions, you should be in good shape for the winter. Do not, however, neglect to consult your owner’s manuals for manufacturer’s recommendations on winterizing your boat and other systems. If you have not done a winterization job before or don’t have an experienced friend to rely on, seek out a professional to do the job for you.

Leave a Reply

Your email address will not be published. Required fields are marked *